Table of Contents

Thin Out Along Node

  • Category: General
  • Edition: Vista Pro with Vista Splines
  • Output type: Positions (1 to 100 sets)
  • Typical place in a graph: after the positions of trees, rocks or grass, before their outputs, to clear them from a road or path

Thin Out Along removes positions along a scene spline: by default it clears everything on the spline's ribbon, so trees, rocks and props stay off a road, path or river. It can take several sets of positions at once and clear them all along the same spline. Turned around, it keeps only what lies along the spline, for hedges or roadside trees.

A dense grid of points with a clear lane where the spline runs

When to use it

  • Keep trees, rocks and props off roads, paths, rail lines and rivers.
  • Keep only what grows along a lane: hedges, an avenue of trees, roadside flowers (Invert off).
  • Not for: clearing by a mask (use Thin Out).

Scene setup

Thin Out Along reads spline evaluators in the loaded scene, by Id, the same way as Path.

Inputs

Slot Type Required What to connect
Position 0 to Position N Positions Yes The sets to thin, one per slot, such as trees, rocks and bushes.
Falloff Detail Mask No Breaks up the edge of the cleared lane, such as a fine Noise.

Outputs

Slot Type What it holds
Position 0 to Position N Positions Each set with the points along the spline removed (or, with Invert off, the points away from it removed).

Properties

Property Default Range What it does
Spline Id PICK_A_SPLINE_ID Text Selects the spline evaluators to read. Type an Id or pick one from the menu next to it.
Falloff 0 at the edge, 1 from halfway in Curve from 0 to 1 The strength of the clearing across the ribbon, from its outer edge (left) to its center line (right), mirrored on both sides. Where it is between 0 and 1, points are removed at random, the same way as Thin Out (an S curve, not a straight proportion).
Invert On On, Off On: remove the points on the spline. Off: keep only the points on the spline.
Input Count 1 1 to 100 The number of position sets to thin.

Common properties

Property What it does
Id The node's unique name in this graph, shown for reference. You cannot edit it. Scripts and the AI workflow CLI use it to find the node.
Split Execution Lets this node run over several frames so the editor stays responsive during long generations. It only works when Allow Split Execution is on in the graph settings. This node finishes in one step, so splitting only adds a short pause around it; leave it off.
Bypass Skips the node. Each set passes through unchanged.

Examples

Scatter every 30 m on a 1024 × 1024 m biome, shown through Dots and Expand.

Invert on (default) Invert off
Points everywhere except a lane along the spline Points only along the spline

Recipes

  • Road through a forest: tree positions, rock positions → Thin Out Along (Input Count 2, the road's Id) → Tree Output and Object Output. Use Ramp with the same Id for the road bed.
  • Avenue of trees: Points along the area → Thin Out Along (Invert off, a narrow Falloff) → Tree Output.
Tip

Make the spline evaluator a little wider than the road mesh, so tree canopies do not hang over the road.

Performance

Cheap: one spline mask is drawn and then one quick GPU step per set.

  • Thin Out: clearing by a mask.
  • Path, Ramp: the same spline as a mask and as a road bed.

For AI agents

  • Type name: ThinOutAlongNode (Vista Pro, Splines module). Inputs Position i = i (Buffers), Falloff Detail = 1000 (Mask); outputs Position i = 100 + i (Buffers).
  • Properties: splineId (string), falloff (AnimationCurve), invertMask (bool, default true), inputCount (1 to 100; not exposable).
  • Measured on the doc spline with a 30 m Scatter: invert on kept most points (Dots mean 0.114 of 0.131), invert off kept the lane only (0.017).